Concrete cutting in Vacaville CA - clean, straight cuts right where you marked them
Need a door in a foundation wall or a broken driveway section taken out? We cut it clean and straight, right on the lines we mark with you.
- Fully licensed and insured.
- Free estimates at your property.
- We reply within 1 business day.
How do you get concrete cut cleanly in Vacaville?
The short answer: Concrete cutting means sawing through a slab or wall with a diamond blade so you get a straight, clean edge, and in Vacaville we do it for driveway sections, garage and shop floors, patios and door or window openings in foundation walls. We're based in Vacaville and work in the cities around it, from Davis and Woodland to Napa, Vallejo and Concord.
Usually there's a piece of concrete in the way of something you want, and the real job is getting it out without cracking what stays. The price mostly turns on how many feet of cut there are, how thick the slab or wall is, whether there's steel inside and how easy it is to get a saw to the spot, while the schedule turns on scanning the slab and on whether the city needs to look at a wall opening first. I put your figure in a written estimate after I've seen the job, and it spells out what's included.
How do you know a slab needs cutting, not breaking up?
One broken driveway section
One panel of your driveway has cracked through or dropped while the rest sits flat. A straight saw cut lets us take out just that piece instead of hammering at it and cracking the good concrete next to it, and the longer it sits, the more water gets under the broken edges and the more they chip.
A wall where you want a door
You want a doorway or window in a concrete foundation wall, and someone has suggested a hammer drill and a chisel. That leaves ragged edges and cracks running out from the hole, while a saw cut leaves a clean rough opening, the hole the door or window frame gets set into.
A new line under the slab
A plumbing repair, a drain or a new electrical run has to go under a garage floor or patio, and the slab is in the way. Cutting a neat trench means we take out only the strip the line needs, so the patch afterward is small and straight instead of a broken mess.
How we do concrete cutting
We start by walking the job with you and marking every cut line on the concrete, because a saw cut can't be put back. Before a blade goes into a slab we want to know what's buried in it, so we'll ask about scanning for rebar, the steel bars that hold a slab together, and for anything else running through it. Then we pick the saw by the surface and cut wet, running water over the blade so the dust turns into a gray slurry instead of a cloud, and once the cuts are through we break out the pieces and leave you a straight edge to build against.
Cutting is often the first half of a bigger job. Once the damaged section is out, we can pour its replacement as part of our concrete driveway building work, or trim an old slab so a new one can join it through concrete patio construction.
Flat sawing for floors and driveways
This is the saw for anything flat, like a driveway section, a patio or a garage floor, and it's the most common kind of concrete cutting. A walk-behind saw rolls along the marked line, so the cut stays straight and holds its depth the whole way.
Wall sawing for door and window openings
When you need an opening in a foundation wall, we run a saw on a track fastened to the wall, which is the standard way to do it. The track holds the blade steady, so the opening comes out square with clean edges ready for framing.
What happens after you call us about concrete cutting in Vacaville?
Here's how a cutting job runs from your first call to the final walk-through, so you know who you'll talk to and what you'll have in hand before you decide anything.
- Step 01
Call or send a request
Call us or use the form and tell us where the cut goes and whether it's in a floor, a driveway or a wall. We get back to you and set a time for me to come out.
- Step 02
I look at the cut myself
I come out, look at the surface, ask what the concrete has to carry once it's cut and where you want the lines. You get a written estimate that spells out what's included, so you know what you're paying for before we start.
- Step 03
We cut, then walk it
If you go ahead, we sort out what the city wants for your address, mark the lines, cut, break out the pieces and leave a clean edge. Then we walk the finished job with you before we pack up.
Concrete cutting permits and slabs in Vacaville
Whether a cut in Vacaville needs a permit depends on what you're cutting, and the city's Building Division is the one that decides, since it reviews and inspects improvements to existing structures inside city limits. A new opening in a foundation wall changes the house itself, so that's the kind of cut to ask about before anything else. We find out what the city or the county wants for the work at your address, and when a permit is needed we pull it, keep the papers on site and meet the inspector. If you'd rather pull an owner-builder permit yourself, the city has you register a Public User account first, which you can do through its building permits page.
A lot of the houses we cut into around here sit on slabs, and you can't tell from the top what's inside one, which is why I ask about scanning before most cuts. We see the same kind of slabs and driveways on jobs in Fairfield and Dixon.
Get a written estimate for your concrete cut
We reply within one business day, then I come out to look at the cut and give you a free written estimate at your property. There's no obligation and no pressure to book.
Why Vacaville homeowners call Custom Vacaville Concrete Company
I come out, my crew cuts
I look at the job myself, and my crew does the cutting and break-out with me running the work. We're based in Vacaville and work the cities around it, and the person who priced your job is the one on site when the saw starts.
Running our own crews since 2013
I started this business in 2013 after years of summers on concrete crews, beginning with the shovel work most people never see. That means I know how a slab was likely built before I cut into it, and I'll tell you straight if a cut isn't worth making.
Fully licensed and insured
We're fully licensed and insured. That matters on a job where a saw goes into the floor or wall of your house, because you shouldn't be the one carrying the risk.
On a cutting job, the line and what's under it matter more than anything, so we settle both before the saw starts. Send us a request or call (707) 898-1384 and I'll come take a look.
Concrete cutting questions from Vacaville homeowners
How much does concrete cutting cost in Vacaville?
Professional concrete cutting across the US usually costs about $3 to $10 per linear foot of cut. That's a national range for the cutting itself, so the figure for your job comes from the written estimate I give you after I've seen it.
Is concrete cutting dusty or wet?
It's mostly wet, because most flat and wall sawing runs water over the blade, which turns the cuttings into slurry instead of dust. California's workplace dust rule lists a walk-behind saw with a built-in water feed to the blade, and wet cutting is how we run our saws, so plan on water and some slurry at the cut.
Can concrete be cut indoors without water?
Yes, dry cutting uses no water and relies on the blade's design and a vacuum to handle the dust. It's used where water isn't practical, such as small hand-saw cuts or some indoor work near finished floors and walls, and I'll tell you at the estimate whether your job calls for it.
Why should a concrete slab be scanned before it's cut?
Because you can't see what's inside a slab, and some of it is dangerous to cut. A contractor's guide warns that cutting a post-tension cable, a steel cable pulled tight inside some slabs, releases energy explosively and can leave the slab unstable, and it calls ground penetrating radar a reliable way to map buried steel and utility lines first. That's why I ask about scanning before we cut into a slab.
What is the best way to cut concrete in a tight corner or right against a wall?
A handheld saw is usually the answer for tight spots, small cuts and flush cuts where a walk-behind or track saw won't fit. On a bigger job we can let the large saw run the long lines and finish the corners by hand.
How do I get ready for a concrete cutting crew?
Know where you want the cut, what surface it's in and where we can hook up water and power, because the saw needs both. A trade association's cutting specification puts the owner in charge of approving the cut location and providing water and electricity, and it has every cut line clearly marked before cutting starts. We mark those lines on the concrete with you, so you approve exactly where the blade goes.
Related concrete work after the cut
Concrete driveway building
When a broken or sunken stretch of driveway comes out, a new pour on a dug-out, packed base helps keep it from settling the same way.
Concrete patio construction
If you're cutting back an old patio to make room for a bigger one, the new slab can be formed right up to the clean saw edge.
Get your concrete cut planned right
Call (707) 898-1384 or send a request and tell us whether it's a floor, a driveway or a wall, so I show up ready to talk about the right saw.